|
Complete Brass and Copper Strip Plant For Sale
(Click each photo to enlarge) 
MACHINERY INTERNATIONAL CORPORATION ANNOUNCES THE SALE OF THIS COMPLETE AND
FULLY INTEGRATED FACTORY FOR THE PRODUCTION OF COPPER, BRASS, AND PHOSPHOR
BRONZE STRIP UP TO 300 MM (12") WIDE. THE PLANT INCORPORATES MELTING, CASTING,
ROLLING, ANNEALING, SLITTING, AND FINISHING.THE PLANT, WHICH WAS INSTALLED IN 2007 AND IS FULLY OPERATIONAL, IS LOCATED NEAR SANTIAGO, CHILE. THE PURCHASE PRICE FOR ALL OF THE MACHINERY, EQUIPMENT AND SPARE PARTS IS SET AT A VERY LOW PRICE TO ENCOURAGE A QUICK PURCHASE AND REMOVAL BEFORE THE END OF THE YEAR AND THIS INCLUDES THE NEARLY $1 MILLION U.S. DOLLARS IN NEW ELECTRICAL AND MECHANICAL COMPONENTS THAT WERE ADDED IN 2006. THE COST TO DISMANTLE THE MACHINERY AND LOAD IT INTO CONTAINERS IS APPROXIMATELY $325,000.00 U.S. DOLLARS. THE PLANT CASTS 70/30 BRASS AND 5% PHOSPHOR BRONZE. OTHER COPPER ALLOYS PRODUCED FROM IMPORTED FEED STOCK INCLUDE C11000, C22000, C23000, AND C75700. STANDARD COIL SIZES PRODUCED ARE 300 MM - 317 MM (12" - 12-1/2") WIDE x 2350 KG (5180 LBS.), WITH THE EXCEPTION OF PRODUCT RUN ON THE SENDZIMIR MILL, WHICH REQUIRES COILS TO BE CUT TO A MAXIMUM O.D. OF 900 MM (35-1/2"). COILS ARE CAST AT 14 MM (0.55") THICK AND ROLLED DOWN ON A BLISS 2-HI MILL AND A SENDZIMIR ZR34-12-1/2 MILL AS THIN AS 0.1 MM (.004"). THE MAJOR EQUIPMENT IN THE PLANT INCLUDES: Click Each Photo for More Pictures
1. METATHERM CONTINUOUS CASTING LINE MELTING FURNACE MANUFACTURER: INDUCTOTHERM MODEL No.: 250-10R TYPE: CORELESS INDUCTION MELTING CAPACITY: 600 KG (1322 LBS.) POWER: 250 KW CONTROLS: ALLEN BRADLEY MODEL 2005 PLC CONTROLS, INSTALLED NEW IN 2007 No. 1 CASTING LINE MANUFACTURER: METATHERM A.S. HOLDING FURNACE TYPE: CHANNEL INDUCTION CAPACITY: 1650 KG (3637 LBS.) POWER: 130 KW STRIP WIDTH: 320 MM (12.6") STRIP THICKNESS: 14 MM (0.55") CASTING RATE: 260 KG/HR. (573 LBS./HR.) WITHDRAWAL UNIT IN-LINE MILLING MACHINE BRUSHING UNIT GUILLOTINE CROPPING SHEAR UPCOILER 
2. No. 2 CONTINUOUS CASTING LINE MELTING FURNACEMANUFACTURER: JUNKER G.M.B.H. TYPE: CHANNEL INDUCTION MELTER CAPACITY: 2500 KG (5510 LBS.) POWER: 300 KW CONTROLS: ALLEN BRADLEY MODEL 2005 PLC CONTROLS, INSTALLED NEW IN 2007 No. 2 CASTING LINE TYPE HOLDING FURNACE: CHANNEL INDUCTION MANUFACTURER: METATHERM A.G. CAPACITY: 1650 KG (3640 LBS.) POWER: 130 KW STRIP WIDTH: 320 MM (12.6") STRIP THICKNESS: 14 MM (0.55") CASTING RATE: 280 KG/HR. (618 LBS./HR.) WITHDRAWAL UNIT CONTROLS: ALLEN BRADLEY MODEL 2005 PLC CONTROLS, INSTALLED NEW IN 2007 MILLING MACHINE MANUFACTURER: TECHNICA GUSS TYPE: 2-SIDED IN-LINE NOTE: RECONDITIONED IN 1997 BRUSHING UNIT GUILLOTINE CROPPING SHEAR UPCOILER 
3. AUXILIARY FOUNDRY EQUIPMENTa. 2-OFF HIGH-TEMP BAGHOUSE DUST COLLECTORS, NEW 1997 2 x DUCTWORK FROM MELTER TO DROPOUT BOX 1 x CHANGEOVER DAMPER 2 x DROPOUT BOXES 2 x DUCTWORK FROM DROPOUT BOX TO FAN 2 x FANS 2 x DUCTWORK FANS TO BAG HOUSES 2 x BAG HOUSES INCLUDING ROTARY VALVES 2 x EMISSION MONITORING EQUIPMENT 1 x ELECTRICAL CONTROL EQUIPMENT FULL ALLEN BRADLEY MODEL 2005 PLC CONTROLS b. COOLING WATER SYSTEM HOT WELL PUMP COLD WELL PUMPS AND CONTROL PANEL COOLING TOWER FULL ALLEN BRADLEY MODEL 2005 PLC CONTROLS c. VIBRATORY DROSS SIEVE d. SCRAP BALER PRESS 
4. BLISS 2-HI BREAKDOWN MILL MANUFACTURER: E.W. BLISS & CO. TYPE: 2-HI NON REVERSING ROLL DIAMETER: 406 MM (16") ROLL WIDTH: 406 MM (16") THICKNESS RANGE BREAKDOWN -(COIL BOX TO UPCOILER): 12.7 MM - 2.3 MM (0.5" - .090") INTERMEDIATE -(REEL TO REEL): 3 MM - 0.38 MM (0.12" - 0.015") DRIVE MOTORS MAIN MILL DRIVE: 300 HP RELIANCE A.C. TAKE-UP REEL: 100 HP RELIANCE A.C. TENSION REEL: 30 HP COIL-TO-COIL REEL: 60 HP A.C. CONTROLS: NEW PLC & VARIABLE FREQUENCY ALLEN BRADLEY A.C. DRIVES, INSTALLED NEW IN 2006. THICKNESS GAUGE TYPE: X-RAY MANUFACTURER: EMC MODEL No.: SXR-76 SCREWDOWNS MOTORIZED MAJOR SPARES 6 x PAIRS OF WORK ROLLS 3 x FULL SETS ROLL CHOCKS 2 WITH BEARINGS 6 x NEW MILL ROLL INNER RINGS 1 x MILL DRIVE SPINDLE 2 x MILL PINION STAND PINION GEARS CARBON BRUSHES FOR MG SETS 
5. 20-HI SENDZIMIR FINISHING MILL MANUFACTURER: W.H.A. ROBERTSON LTD. TYPE: 20-HI REVERSING Z-MILL MAXIMUM STRIP WIDTH: 317 MM (12.5") CURRENT THICKNESSES * -MAXIMUM ENTRY: 1.2 MM (0.050") -MINIMUM FINISH: 0.1 MM (0.004") * NOTE: MILL ITSELF CAN GO THICKER & THINNER DEPENDING ON ALLOY MAXIMUM TENSION: 2500 KG @ 91 M/MIN. (5500 LBS. @ 300 FPM) SPEED RANGE: 45 - 90 M/MIN. (150 - 300 FPM) MAIN DRIVE MOTOR: 40 HP, 333/666 RPM WINDER MOTORS (2): 50 HP, 41/82 RPM DRIVE CONTROLS: EUROTHERM ELECTRONIC D.C. DRIVES, INSTALLED 2003 AUTOMATIC GAUGE CONTROL (AGC) MANUFACTURER: VOLLMER MODEL No.: VBM 1076 ELECTRONICS: VMF ELECTRONICS, NEW 2003 YEAR OF MANUFACTURE: 1961 YEARS OF UPGRADES: 1985, 1988, 1999, 2002, 2003 MAJOR SPARE PARTS 15 x SETS (SET=2) WORK ROLLS 6 x SETS 1ST INTERMEDIATE ROLLS (SET=4) 7 x SETS DRIVE ROLLS (SET=4) 7 x SETS IDLE ROLLS (SET=2) 4 x SETS BACKUP BEARINGS INCLUDING 1 ST IN MILL 1 x VOLLMER AMPLIFIER MODEL VMF 3-22 2 x SPARE SOLID BLOCK COILERS 
6. BELL ANNEALING FURNACES TYPE: NATURAL GAS-FIRED YEAR OF MANUFACTURE: 1992/1997 No. OF FURNACES: 3 No. OF HEARTHS: 6 CAPACITY - 4 HEARTHS: @ 7500 KG (16,535 LBS.) - 2 HEARTHS: @ 5500 KG (12,125 LBS.) TYPE OF ATMOSPHERE: NITROGEN/HYDROGEN W/MIXING PANEL FED FROM BULK STORAGE CONTROLS: NEW ALLEN BRADLEY PLC CONTROLS, INSTALLED IN 2007 
7. ACID CLEANING/PICKLING LINE UNCOILER STITCHER ACID SPRAY TANK RINSE TANK/STEERING ROLL BRUSHING STATION ANTI-STAIN TREATMENT TANK AIR KNIFE ELECTRIC DRYER EDGE CONTROL RECOILER NEW ALLEN BRADLEY PLC CONTROLS, INSTALLED IN 2007 LINE CAN BE RUN AS A DEGREASER BY SWITCHING FROM RECYCLED RINSE WATER TO DEGREASING SOLUTION IN THE BRUSHING STATION. OLD EFFLUENT TREATMENT PLANT (NOT INSTALLED) NEUTRALIZING TANK PRIMARY SETTLING TANK FILTER BANGS FILTER TANK SECONDARY SETTLING TANK MONITORING TANK DISCHARGE TANK pH CORRECTION CONTROLLER AND DOSING PUMP FLOCCULANT DRUM AND DOSING PUMP ASSOCIATED PUMPS, LEVEL CONTROL EQUIPMENT, DEGREASING SOLUTION TANK AND FLOW METERS 
8. 450 MM (17.5") BROOKES SLITTING LINE MANUFACTURER: BROOKES & CO. LTD. MAXIMUM WIDTH OF STRIP: 450 MM (17.5") MAXIMUM THICKNESS OF STRIP: 0.8 MM (0.03") MINIMUM THICKNESS OF STRIP: 0.127 MM (0.005") TYPE SEPARATORS: FINGERBOARD SCRAP WINDER RECOILER W/PUSH-OFF PLATE DOWNENDER COIL CONVEYOR ROLLER TABLE 
9. 330 MM (13") RUESCH RING SLITTER MANUFACTURER: H.J. RUESCH & CO. TYPE: RING SLITTER MAXIMUM WIDTH OF STRIP: 330 MM (13") MAXIMUM THICKNESS OF STRIP: 0.8 MM (0.0315") MINIMUM THICKNESS OF STRIP: 0.127 MM (0.005") SCRAP WINDER RECOILER W/PUSH-OFF PLATE DOWNENDER COIL CONVEYOR ROLLER TABLE 
10. 400 MM (15.7") BLISS SLITTING LINE MANUFACTURER: E.W. BLISS CO. MAXIMUM WIDTH OF STRIP: 400 MM (15.7") MAXIMUM THICKNESS OF STRIP: 0.9 MM (0.035") MINIMUM THICKNESS OF STRIP: 0.05 MM (0.002") ENTRY PAYOFF EXIT WINDER SCRAP WINDER 
11. WATERBURY FARREL SLITTING LINE, REVAMPED 2006SLITTER RECOILER WITH PUSH-OFF PLATE DOWNENDER COIL CONVEYOR ROLLER TABLE 
12. 356 MM (14") UNGERER LEVELLING LINE MANUFACTURER: FRITZ UNGERER CO. G.M.B.H. MODEL No.: 600/1/19 No. OF ROLLS: 19 MAXIMUM WIDTH OF STRIP: 356 MM (14") MAXIMUM THICKNESS OF STRIP: 2 MM (0.080") MINIMUM THICKNESS OF STRIP: 0.2 MM (0.008") PAYOFF REWINDER DRIVE: 11 KW TENSION CONTROL: UPGRADED IN 2000 13. ARYMA CIRCLE CUTTER (7924) MANUFACTURER: ARYMA MACHINE CO. MODEL No.: KS 3 800 YEAR OF MANUFACTURE: 1982 
14. HEINE CUT-TO-LENGTH LINEMANUFACTURER: JOHN HEINE & CO. LTD. YEAR OF MANUFACTURE: 1983 YEAR RECONDITIONED: 2005 15. PACKING EQUIPMENT 2 x PLATFORM SCALES 1 x PACKING TABLE 1 x PLASTIC BANDING MACHINE HAND-OPERATED STRAPPERS 
16. SLITTER CUTTER GRINDER17. PANCAKE RECOILER 18. TESTING EQUIPMENT VICKERS HARDNESS TESTER TENSILE TESTING MACHINE 19. MITER WOOD SAW AND TABLE WOOD DUST COLLECTOR **PRICE QUOTED IS EX WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE** **ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER** Price Available Upon REquest
You are receiving this e-mail because you signed up for our
mailing list. If you no longer wish to receive e-mails from us,
please reply with "REMOVE" in the subject. Thank you.
Machinery International Corporation considers the privacy of its
users to be of utmost importance and works to protect it.
Machinery International Corporation uses customer information for
internal purposes only. We will not sell or share your information
with outside parties. |